 |
| |
6213A IN Insulation Testers
Up To 10 kV
|
 |
|
|
FEATURES |
| |
 Smart microprocessor controlled. |
| 2 x 16 characters, large, High Contrast, Intelligent L.C.D. Module. |
| 20 Insulation test voltages. 500V, 1kV, 1.5kV, 2kV, 2.5kV, 3kV, 3.5kV, 4kV, 4.5kV, 5kV, 5.5kV, 6kV, 6.5kV, 7kV, 7.5kV, 8kV, 8.5kV, 9kV, 9.5kV, 10kV |
| Calculate Dielectric Absorption Ratio (DAR) automatically. |
| Calculate Polarization Index (PI) automatically. |
| Insulation resistance Auto-Ranging on all ranges. |
| Ener-Save (tm). |
| Bargraph indicates test voltage. Rise and decay can be observed. |
| Warning of external voltage presence (>500Vac or Vdc). |
| Overload protection. |
| Low battery indicator (real time battery Voltage Measurement). |
| Measure insulation time duration of the test. |
| Low battery consumption. |
| Better than 10% accuracy on all ranges. |
| Auto-off. |
| :2001, EN 61326-1, EN 55011, EN 61000-3-2, EN 61000-3-3, EN 61000-4-2, EN 61000-4-3, EN 61000-4-8 |
|
| DAR = Eielectric Absorption Ration. The dielectric Absorption Ratio is the ratio of the Insulation Resistance measured at 1 Min divided per the insulation Resistance measured at 30 seconds. 30 seconds after starting a test (with EnerSave (tm) disabled), the tester will beep, indicating the operator that the resistance value measured at 30 seconds now has been saved internally. 1 Minute after starting a test (with EnerSave (tm) disabled), the tester will beep again, indicating the user that the DAR result is now computed, and change the dispaly format to now display the DAR result. |
| PI = Polarization index. The Polarizatin index or PI is the ratio of the Insulation Resistance measured at 10 Minutes divided per the insulation Resistance measured at 1 Minute. 10 Minutes after starting a test (with EnerSave (tm) disabled), the tester will beep again, indicating the user that the PI resuit is now computed, and change the display format to now display the PI result. The tester will Auto-Stop at 10 minutes. |
| Digital Dispaly : The digital Liquid Crystal Dispaly is large. It measures 98mm(W) x 24mm(H) and has 2 Lines of 16 Characters. Language can be changed on demand, as an option. Dutch /French / German etc... (factory fitted at order) |
| Automatic Battery Test. When the tester starts, it test its batteries by drawing a heavy current from the batteries. During that heavy current, it measure the battery voltage and displays it for a few seconds on the display. Durig normal use, the tester monitors the battery voltage, but without drawing a battery test current. It just measures the battery while in normal use. |
| Automatic Discharge of Capacitive and Inductive Circuits. This tester will discharge automatically all circuits charged by the tester, after a test is done, again, this will only be activated if the test leads make contact at any time before, during and after the test. |
| It is your responsibility to ensure proper contact of the leads at all times. Once a test is finished, the testers will automatically discharge capacitive or inductive circuit of their charge. The discharge can be observed on the display in the form of a bar-graph. Again, do not disconnect the leads while discharging. Wait until completion of the discharge before removing any lead. During discharge, the Buzzer will beep and the bar-graph will show some voltage. With some high charges, this may take some time. Be patient and let the instrument discharge completely before proceeding to removing the leads. |
|
| SPECIFICATIONS |
| |
| Test Voltage |
From 500Vdc to 10KVdc adjustable in 500 V steps |
| Preset Buttons |
1kV, 2.5kV, 5kV, 10kV |
| Measuring Range |
800K Ohm ~ 500G Ohm (auto-ranging) |
| Accuracy |
+/- 5% +/- 2 digits |
| Optput Power Limit |
1W |
| Voltage Regulation |
Selected voltage +20%-5% of nominal vlaue unless current limited. Meaning that if ouotput current is too high, the voltage will be lowered automatically |
| Weight |
Appox. 3.6kg |
| Dimensions |
330(L) x 260(W) x 160(D)mm |
| Power Source |
8 x 1.5V Alkaline batteries |
| Accessories |
Color coded flexible silicone test leads |
| |
Instruction manual |
| |
Batteries |
|
| 特 點--數位高壓電絕緣測試計(1kV以上)6213A IN |
 ● 使用微處理器系統控制設計。
● 使用2(行) x 16(字)液晶顯示器。
● 液晶顯示器呈現斜度，方便識讀。
● 設計有4個固定電壓檔位,可以視實際需要,每500V為一單位,予以增減。
● 有20個測試電壓檔位：
500V，1kV，1.5kV，2kV，2.5kV，3kV，3.5kV，4kV，4,5kV，5kV，5.5kV，
6kV，6.5kV，7kV，7.5kV，8kV，8.5kV，9kV，9.5kV，10kV
● 自動換檔。
● 省電功能設計。
● 量測電壓有類比刻劃指示。
● 外來電壓(大於AC/DC 500V)警示設計。
● 過載保護設計。
● 量測時間顯示。
● 電池電源不足顯示。
● 具有電介質吸收比(DAR)和極化指數(PI)自動功能。
● 自動關機。
● 通過歐洲安規驗證
EN 61010-1 CAT III 300V
EN 61326-1 |
|
| 規 格 (23°C±5°C ＜80%R.H.) |
| 控制方式 |
微處理器控制系統 |
| 量測檔位 |
500V~10kV : 每500V為一個單位，
可從固定電壓鍵(1kV, 2.5kV, 5kV,
10kV)作累加或遞減 |
| 固定測試電壓鍵 |
1kV, 2.5kV, 5kV, 10kV |
| 量測範圍 |
800kΩ~500GΩ(自動換檔)
25GΩ/0.5kV→500GΩ/10kV |
| 容許誤差 |
±5%讀值±2位數 |
| 電介質吸收比(DAR) |
ˇ |
| 極化指數(PI) |
ˇ |
| 外形尺寸 |
330(長) × 260(寬) × 160(高)mm |
| 重量 |
約3600g |
| 使用電池 |
1.5V “C”× 8 鹼性電池 |
|
|
| 特 點---絕緣測試計(OLED顯示)6213A IN-M |
 ● C對比的OLED顯示，非常容易識別，提供給礦業或其他在黑暗處工作的行業量測使用。
● 微處理器系統控制設計。
● 使用2(行) x 16(字)液晶顯示器。
● 液晶顯示器呈現斜度，方便識讀。
● 有20個測試電壓檔位：
500V, 1kV, 1.5kV, 2kV, 2.5kV, 3kV, 3.5kV, 4kV, 4.5kV, 5kV, 5.5kV, 6kV, 6.5kV,
7kV, 7.5kV, 8kV, 8.5kV, 9kV, 9.5kV, 10kV。
● 自動換檔。
● 省電功能設計。
● 量測電壓有類比刻劃指示。
● 外來電壓(大於AC/DC 500V)警示設計。
● 過載保護設計。
● 量測時間顯示
● 電池電源不足顯示
● 自動關機
● 通過歐洲安規驗證 : EN 61010-1 CAT III 300V
EN 61326-1 |
|
| 規 格 |
| 控制方式 |
微處理器控制系統 |
| 量測檔位 |
500V-10kV
每500V為一0-200MΩ個單位，可
從固定電壓鍵(1kV, 2.5kV, 5kV,
10kV)作累加或遞減 |
| 固定測試電壓鍵 |
1kV, 2.5kV, 5kV, 10kV |
| 量測範圍 |
800kΩ-500GΩ(自動換檔)
25GΩ/0.5kV→500GΩ/10kV |
| 容許誤差 |
±5%讀值 ± 2 位數 |
| 電介質吸收比(DAR) |
ˇ |
| 極化指數(PI) |
ˇ |
| 外形尺寸 |
330(長)x260(寬)x160(高)mm |
| 重量(含電池) |
約3.6公斤 |
| 使用電池 |
1.5V x 8(顆). C型. 鹼性電池 |
|
|
|
